General-purpose

CASING

Casing construction bases on the spacious frame made of aluminum profile. Casing panels has the insulation made of 45 mm thick mineral wool and 50 mm. Casings of each section have the inspection panels equipped with the clamps and grips. Casing parameters according to the EN 1886 standard: heat infiltration coefficient U=1,17 W/m2K – class T3  heating bridges influence coefficient – class Tb1, mechanical strength of the casing - class 1, leak tightness - class B, working temperature in standard version from -40C to +90C

BASES AND FEET

The units use bases or feet made of galvanised sheet metal. The height of the feet and bases depends on the unit size.

ROOF

The external versions are additionally equipped with the roof protecting them against atmospheric precipitation.

FLEXIBLE CONNECTORS

Flexible connectors protect the duct system (installation) against carrying the vibrations from the unit. They also serve to minimize the misalignment of ventilation channels. Connecting frames are made of galvanized steel.

AIR INTAKE AND AIR EXHAUST COWLS

The external versions can be additionally equipped with the air intakes and/or air exhausts.

AIR DAMPERS

Depending on the configuration, the unit can be equipped with one or several air dampers. They operate as shut-off, control and protection devices. The standard blades of the air dampers are made of aluminium. The blades in the untypical solutions can be made of galvanised or stainless steel.

FILTERS

The standard units can be equipped with panel or bag filters G4-F9 class filters. The untypical solutions can use higher H10-H13 class filters.

WATER HEATER

copper tubes with diameter f10, f12, f16 › aluminum fins, fins spacing: f10 - 2,0; 2,4; 3,0mm, f12 - 2,0; 2,4; 3,0mm, f16 - 2,4mm

WATER HEATER FOR HIGH PARAMETERS

core – steel pipe wound – thick - walled aluminum pipe rotationally cold-rolled; › fins spacing 2,8 mm; core pipe diameter 16 mm; casing made of galvanized sheet, average rib thickness 0,3 mm; number of rows 2-10;

STEAM HEATER

core – steel pipe; wound – thick- walled pipe rotationally cold-rolled; › louver spacing 2,8 mm or 0,5mm; core pipe diameter 25mm; casing made of galvanized sheet; average rib thickness 0,3mm;

WATER COOLING COIL

copper tubes with diameters f10, f12, f16 › aluminum fins, fins spacing: f10 - 2,0; 2,4; 3,0mm, f12 - 2,0; 2,4; 3,0mm, f16 - 2,4mm , casing made of galvanized sheet

FREON EVAPORATOR COIL

copper tubes with diameter f10, f12, f16, aluminum fins with spacing:
f10 - 2,0; 2,4; 3,0mm, f12 - 2,0; 2,4; 3,0mm, f16 - 2,4mm

GAS HEATER

Gas exchangers are intended for heating the air with using the gas fuels as well as liquid fuels. Air is heated thanks to flowing on the combustion chamber surface and bunch of exchanger tubes. Power regulation depends of used burner and it could be: modulated, two-leveled, ON/OFF

REFRIGERATION SYSTEM

Cooling system consists of the evaporator and the condenser as well as scroll type compressor. Evaporator and condenser are made of copper tubes with the tubes aluminum fins pack. Compressors are placed on vibro-insulators. Cooling circuit consists of: filters and cooling medium dryers, thermostatic expansion valve, low and high pressure switches, low and high pressure manometers, regulation and protecting circuits and cooling fittings. As the cooling medium the R407c,R410A is used. Cooling system can be used for supply/exhaust units with cold recovery on cross-flow exchanger.

PLATE HEAT EXCHANGER

assembly of redrawn plates made from: » aluminum, epoxy coated aluminum, exchanger by-pass, drip tray made from acid-resistant sheet, drop separator, plates spacing depends on exchanger type – from 5 to 12 mm,

ROTARY HEAT EXCHANGER

types of rotors: condensating intended mainly for heat recovery. Moisture recovery is made only in case when exhaust air is cooled below the dew-point. enthalpy regenerator has the hygroscopic coat supporting the moisture exchange, sorptive with strong hygroscopic coat enabling very effective heat and moisture recovery through the whole year, condensation epoxy coated increasing the resistance to corrosions. drive with adjusted rotational velocity with belt transmission, brushing circumferential and lateral seals, used in the units with up to 1750 mm storey height, working environment from -40°C to +80°C, The rotational speed of the heat exchanger is, controlled by the inverter, delivered with the heat exchanger, as a standard.

EXCHANGER HEAT PUMP

assembly of redrawn plates made of aluminum › casing made of galvanized sheet, exchanger by-pass, drip tray made of acid-resistant sheet, drop separator

DIRECT DRIVEN FAN

fan and motor assembly placed on one frame, rotor installed on motor shaft, vibro-insulators and flexible flange cutting off the vibrations from the unit casing, fluent regulation of rotations with the frequency converter, manufacture standards: standard, epoxy coated, explosion proof Ex

BELT DRIVEN FAN

fan and motor assembly placed on one frame, radial fans with double suction with the blades inclined backward or forward, indirect drive through the belt transmission, taper-lock type wheels enabling using huge variations of wheels, three-phase motors, vibro-insulators and flexible flange cutting off the vibrations of the assemblyu from the unit casing, manufacture standards: standard, epoxy coated, explosion proof Ex

SILENCER

damping cartridges (slotted levers) made of mineral wool, external surfaces of slotted levers covered with thin cloth “veil” type in order to eliminate infiltration of mineral wool parts to the air

DROPLET ELIMINATOR

panels of the drop separator made of plastics, specially shaped profile enabling effective catching the water particles, panels thickness 130 mm, maximal flow velocity 4m/s, minimal velocity 2m/s, below this value use of the drop separator is not required, section equipped with the tub made of acid-resistant sheet

SIGHT HOLE

round inspection window built in the inspection door, enables monitoring of the unit interior during its operation › used mainly in the units in hygienic version

LIGHTING

rectangular glow discharge tubes, enable monitoring of the unit interior during its operation, used mainly in the units in hygienic version, power supply 24V

STANDARD VERSIONS AIR FLOW 500 - 135 000m3/h

All the units elements are made from following materials:  internal casing panels made of galvanized sheets, external side panel and upper panel made of aluzinc type sheets, flor panels are made of galvanized sheet, all the slots on the contact with casing elements are filled with silicone, door panels seals are made from EPDM; rails and slideways working with withdrawable elements, filters frames, heat exchangers casings, fans partitions are made of galvanized sheet; drip trays under the cooling coils and heat recovery exchangers are made of stainless steel, drainage of condensate protected against drawback with the help of siphons, bases of units made of galvanized steel